Skip to main content

Seeing as how I’m sort of “between projects” right now (waiting on parts for 3 projects!), I decided to try to repair my LionChief Polar Express PCB. This board came in a 1225 I bought thru the Bay as parts only, and I found that the board worked, but VERY intermittently. So intermittently, that most of the time it just didn’t work. When it did work, everything worked - when it didn’t work, the Universal controller acted as though it had lost the signal.

IMG_1849The board

So a closer examination showed just 3 possibilities for parts replacements, a 16.0Mhz crystal (lower left corner on the receiver board) and a couple of electrolytic caps (lower right corner on the main board), all parts that were available from Digikey. I replaced them this evening and found … no change. I previously had reheated/reflowed all accessible connections with a VERY fine point on my soldering pencil, also with no change.

So in one last desperate measure, I applied the finger test – this is a test where you stick your finger everywhere, mostly to see if a part is getting hot – judicious application is required under those circumstances. But it also can reveal other things. In doing this, I noticed that when my finger got closer to the little black glob on the receiver board, things started to stabilize. If I rested my finger on the black blob, I had a steady signal 100% of the time. Hmmm, a crude RF link… So I looked for a broken antenna connection – apparently they are using the little zig-zag foil section of this board as the actual antenna – appears like a 2.4Ghz type of signal must be used to have an antenna of this style. Two SMD caps are feeding this antenna – I reheated the connections at this point … no change. So as a last desperate act, I soldered a 6” wire to the last cap … BOOM! Not only is the signal reliable without the help of my finger, but now I can even walk into my garage to control my train in the basement (frankly not what I was trying to accomplish) – previous best range was about 10ft.

IMG_1847The fix

So I guess even a blind squirrel finds a nut now and again. For just a couple of dollars in parts that I didn’t need, and a little time, I have regained the use of a now redundant PE 1225 board – yeah, I bought a new PCB back in January and fixed the engine right up. So I’m guessing this one may find a home in a slope back tender behind a 1615 or a 1662 switcher, or maybe a 2018! Hmmm, or maybe behind an engine with a DC motor - almost forgot! I just have to remember to NOT push the crew talk button, lest Tom Hanks speaketh out awkwardly.

Just thought I would share – never know who might have a similar problem … plus I was tickled pink to have repaired it!

George

Attachments

Images (2)
  • IMG_1849
  • IMG_1847
Last edited by GeoPeg
Original Post

Replies sorted oldest to newest

Jayhawk500 posted:

Way cool. If I want to increase my range I now have a fix.

Maybe … that's no guarantee. I believe my issue was and still is a corroded trace and/or solder joint at the junction of an SMD capacitor and the actual antenna foil. By soldering my antenna wire directly to the output at the cap, I am bypassing the defective connection and the zig-zag foil trace antenna.

So I was fixing a defect - if yours is working normally, and you add a new single wire, 6" antenna, your performance could be better or worse than using just the board's original zig-zag foil trace antenna because you have now added a second antenna, in parallel with the first (zig-zag foil) antenna. And there is no easy way to separate the zig-zag foil trace from its connection point at the cap, other than cutting the trace. I have no idea how well that will work.

Only way to tell for sure is to do some testing with side-by-side units, something I'm not going to bother to do as long as I have the good range afforded by the 6" wire! If I had to bet, I would say there's probably very little difference between the two.

If you're determined to try it, be prepared to use a VERY fine soldering tip! I had to use a really strong magnifier to see what I was doing - VERY tiny stuff!

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Ste 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×