Skip to main content

Just for fun, I worked-up a version of Garrett's 4x13 design (4x12 later posts) from his thread at THREAD, [its a good thread, with pictures and a video - check it out] adding some features that go beyond his Christmas layout for a concept for a more permanent layout, adding reverse loops and cross-overs.   Outside diameter is O44 compound - should run most O42 equipment.  The inside route is O36 minimum.   With easements of O48 and O72.   The curving lower middle section is O72.  Turnouts are O60 and O48.  Add spurs where you like.  -Ken

M413F-Forum_V1b

Last edited by Ken-Oscale
Original Post

Replies sorted oldest to newest

Adding some spurs:

M413F-Forum_V1e

The curve in the middle beneath the crossing are two O96 sections.   The track center spacing is 4.25", which is tight but works fine for O-36 traditional equipment, even the LionChief+ SD60M and Berkshire with passenger cars on my layout.

Turnouts are now O72 and O48:  there are two O72 turnouts at the bottom making the reverse curves.

The plan has three routes: the outside perimeter loop, the inside return-loop to return-loop, and the twice-around through the crossing.

Attachments

Images (1)
  • M413F-Forum_V1e
Last edited by Ken-Oscale

Thanks very much for your kind words gentlemen!

This next is the logical continuation, now to a form not at all resembling Garrett's design from his thread, but instead, looks like some of my earlier designs posted to this forum.   Here, the crossing is replaced with turnouts, and a fourth route is created:   1) Outside loop, 2) Inside loop, 3) Inside reverse-loops, 4) twice-around through the cross-overs.

M412F-V1k

Attachments

Images (1)
  • M412F-V1k

Hi Bigjon78, here is a list (unsorted) as it comes from AnyRail.  Copy and paste it to sort it.

Remember that two1-3/8" sections come with each O60 turnout, included in the total for those sections.

Hope this helps - Ken.  Thanks for the interest in this plan!

Track
2-105 (S60), H0 Kato Unitrack, Straight 2 3/8". 3
2-111 (S94), H0 Kato Unitrack, Straight 3 11/16". 1
2-152 (S246PC), H0 Kato Unitrack, Straight (concrete) 9 11/16". 1
2-170 (S109B), H0 Kato Unitrack, Buffer/Bumper 4 9/32". 1
2-260 (R430-22.5), H0 Kato Unitrack, Curve radius 16 15/16", angle 22.5º 13
2-270 (R490-22.5), H0 Kato Unitrack, Curve radius 19 9/32", angle 22.5º 4
2-840 (HP-490L), H0 Kato Unitrack, Left turnout 9 11/16". (manual) 1
6-12014, 0 Lionel FasTrack, Straight 10". 7
6-12015, 0 Lionel FasTrack, Curve 18", angle 45º (O36) 8
6-12022, 0 Lionel FasTrack, Curve 18", angle 22.5º (O36) 1
6-12023, 0 Lionel FasTrack, Curve 18", angle 11.25º (O36) 12
6-12024, 0 Lionel FasTrack, Straight 5". 5
6-12025, 0 Lionel FasTrack, Straight 4 1/2". 6
6-12026, 0 Lionel FasTrack, Straight 1 3/4". 5
6-12035, 0 Lionel FasTrack, Buffer/Bumper (Light) 5". 3
6-12042, 0 Lionel FasTrack, Straight 30". 4
6-12043, 0 Lionel FasTrack, Curve 24", angle 30º (O48) 8
6-12073, 0 Lionel FasTrack, Straight 1 3/8". 26
6-16824, 0 Lionel FasTrack, Left turnout 10". (O36) Command Control 1
6-16825, 0 Lionel FasTrack, Right turnout 10". (O36) Command Control 1
6-16828, 0 Lionel FasTrack, Left turnout 13 1/8". (O60) Command Control 2
6-16829, 0 Lionel FasTrack, Right turnout 13 1/8". (O60) Command Control 2
6-16830, 0 Lionel FasTrack, Left turnout 15". (O48) Command Control 3
6-16831, 0 Lionel FasTrack, Right turnout 15". (O48) Command Control 2
6-16834, 0 Lionel FasTrack, Curve 24", angle 15º (O48) 8
6-16835, 0 Lionel FasTrack, Curve 24", angle 7.5º (O48) 17

Add Reply

Post
The Track Planning and Layout Design Forum is sponsored by

AN OGR FORUM CHARTER SPONSOR
×
×
×
×
Link copied to your clipboard.
×
×