Skip to main content

I recently converted from 3-rail Lionel tubular to Fastrack.  While I'm loving the look, and for the most part, the operation of the trains on the new track, my first experience with their pre-wired track activation sections was a waste of money and a disaster.  Those sections actually come in the box with 3 sections of track: one 10 inch straight section with no continuity between the outer rails, and two 1/2 inch straight sections to be placed on either side of the 10 inch section.  The two 1/2 straights isolated one of the outer rails and the full straight acts as a switch for accessories and relays.  (With the old tubular track, you could easily make a section yourself from one piece of regular straight track.)  In the package, the two 1/2 straights have to be taken apart.  For some reason, the factory snaps them together for packaging and shipment.  With all 3 brand new track activations packages, when I attempted to disassemble the two 1/2 straights, the center pin on one of them practically disintegrated, or got lodged in the track with which it was mated.  For the 1/2 section that was not impacted, when I attempted to mate these to the 10 inch section, the same problem happened.  Unfortunately, rather than return these for a refund, I attempted my own fix.  I was successful on my second and third attempt, but completely destroyed the first one.  Bottom line...These activation track sections are complete garbage.  Do NOT buy them.  For some reason, the center pins on these completely lack any structural integrity.  I have assembled and disassembled regular Fastrack straights and curves and did not have this problem.  Lionel should really be ashamed of itself for producing and selling this product.  As a 60-year veteran model railroader, I have never seen such poor quality and workmanship in a product, not even on an old Marx set that I had when I was a boy.  Hey Lionel...Boo...Hiss!!!

Last edited by HR Guru
Original Post

Replies sorted oldest to newest

Steims...No, I am not using the plug and play, but my dealer told me that this is new production for the traditional ones.  I think you are correct about a recent production problem.  I was completely flabbergasted when the center pins practically disintegrated into small bits.  What a shame.  Some other O Gauge friends have indicated that these are easy to make.  I watched a video and actually did one myself.  But easy?  After you loosen the tabs on the rails, if you are not very careful, you won't be able to get the rail to sit flush with the road bed when you attempt to put them back in.  I'm hoping I didn't make a mistake by going with Fastrack.  A part of me really wanted to stay with the traditional tubular.  As I said in my original post, so far I'm really loving the look. 

I'm planning on buying some starter sets this Xmas for my grandkids.  I think I may go with Williams starter sets and the traditional track.  It is likely that their parents will put these sets around the tree for a couple of years.  I'm thinking that the Fastrack pieces will not stand up to that.

Thanks again for responding (and thanks to everyone else too).

HR Guru posted:

 I watched a video and actually did one myself.  But easy?  After you loosen the tabs on the rails, if you are not very careful, you won't be able to get the rail to sit flush with the road bed when you attempt to put them back in.

There's no reason the track should lift by just removing the cross connectors, I've done dozens of them and I didn't even think about that issue.  It's actually harder than you think to lift the track up, that shouldn't be an issue.  Remember, you're only bending a couple of the tabs, not all of them.

Thanks GunRunner.  I can do that but I guess I'm stuck on why the system isn't simple enough that I should not have to.  I'm less of a builder and technician of layouts and more the type that just wants to run the trains.  Also I think the design engineers at Lionel should have anticipated the need for a simple track activation section with one isolated rail and good old fashioned fiber pins.  Remember those?  Easy peasy.   I have a few motion activated activation devices left over from my last layout.  I can use those.

Well, they do have Fastrack insulated rail sections, so they did somewhat anticipate it.  Personally, when I wanted an insulated track run, I either took the connector bars out or used the insulated track sections.  For the ends of the insulated section, I either use the Dremel to simply sever the track rail or lop off the connecting pin on that track segment.

Add Reply

Post
×
×
×
×
Link copied to your clipboard.
×
×