Skip to main content

I picked up a paint pen from wally world and tested it out on a piece of flex. it didn't adhere that great. should I wipe it down with something first?  also getting to the inside with that pen was a little tough.. should I just brush it? im just wondering if im opening a can of worms with this.

Original Post

Replies sorted oldest to newest

I use airbush, either way you have to clean the oils from hands and manufacturing process or it wont stick.

Originally Posted by domer94:

       

I picked up a paint pen from wally world and tested it out on a piece of flex. it didn't adhere that great. should I wipe it down with something first?  also getting to the inside with that pen was a little tough.. should I just brush it? im just wondering if im opening a can of worms with this.

If you haven't ballasted the track yet, it is very simple. I used a Charcoal Green spray can by Rustoleum (which is no longer produced, but some sort of 'Camo Brown' is now available). I sprayed both sides of the 3 rails, including the ties. When the spray paint began to set, I wiped the tops of the rails with a lacquer thinner moistened red cotton rag, wrapped around a piece of 1" X 2" wood. One or two days later, I spray painted more track, using the same process.

Most of the layout has been, or will be getting airbrushed after the track is down and wired. Yes...paint the center rail. NO- is does not effect the DCS, or TMCC/Legacy signals. The paint does not create any voltage drops. Just make sure all your joints are tight when putting the track down.

 

20150507_131905

20150507_131950

20150507_132005

 

These storage tracks and switches were painted outside with camo flat brown spray cans, and then installed, just because it was easier.

 

IMG1905

 

1st level of texture and weathering applied to the spray bombed storage tracks.

 

20141125_195218

Attachments

Images (5)
  • 20150507_131905
  • 20150507_131950
  • 20150507_132005
  • IMG1905
  • 20141125_195218
Originally Posted by domer94:

pretty cool. so you painted rails and ties ..everything? did you hang them and spray?

I didn't. The whole layout had the track & turnouts laid on VinylBed roadbed, completely wired and totally finished, THEN I spray painted all the track/turnouts, cleaned the rail tops, and some days later, I sprayed some more, until the whole layout had all the track/turnouts completely weathered. Then, and only then, did we begine ballasting and scenery.   

Originally Posted by domer94:

pretty cool. so you painted rails and ties ..everything? did you hang them and spray?

the track that was sprayed outside with spray cans was laid on cardboard, and everything was covered. ties, rails, frogs... everything

 

the airbrushed track was focused on the rails only, but of course the ties get some paint too. no big deal though because when you ballast and weather the tracks, it all blends together nicely 

I used Floquil rail brown on my main line and a mixture of rail brown and grimy black for yard tracks. I paint lightly used rails with Floquil rust and weathering chalks.

With Floquil no longer produced I'll have to find a substitute when my supply runs out.

When I'm finished, I clean the rail tops with a solvent.

CN StPaul

Attachments

Images (1)
  • CN StPaul

About a month ago, I bought a WS rusty rail paint pen.  I found that I had to clean the sides of the rail with alcohol or else the pen tip picked up stain (traces of which were left from when I stained the ties) and stopped working.  I didn't have much problem getting sides of the rails painted except on switches.  I bought 2 more paint pens a few weeks ago.  It looks OK...more realistic than shiny tin.  But not as nice as some the guys that use an airbrush.

 

 

 

 

 

 

This section of abandoned track was painted using all powders then sealed with a dull coat. Best success I've had yet. Even better the closer you zoom in the better it looks because of the grit from the powders. Engine House with lights [14)

 

This section was airbrushed using Testors Model Master Enamel Raw Umber and then regular enamel Testors flat Brown. IMG_20141226_124829525_HDR

 

Attachments

Images (2)
  • Track
  • IMG_20141226_124829525_HDR

Joe I've never had an issue with losing electrical conductivity after painting track on any of the layouts I've done, N scale, HO, or O. The key is making all your rail joints tight when you install the track, which you should do anyway.

 

I recently bought this airbrush to finish up painting the track on the unfinished half of the layout:

  

Airbrush

Attachments

Images (1)
  • Airbrush
Last edited by Former Member
Wow that sure is a top of the line airbrush you have there!!!! I'm jealous!!!!



Originally Posted by Laidoffsick:

       

Joe I've never had an issue with losing electrical conductivity after painting track on any of the layouts I've done, N scale, HO, or O. The key is making all your rail joints tight when you install the track, which you should do anyway.

 

I recently bought this airbrush to finish up painting the track on the unfinished half of the layout:

  

Airbrush

Laidoffsick posted:

Most of the layout has been, or will be getting airbrushed after the track is down and wired. Yes...paint the center rail. NO- is does not effect the DCS, or TMCC/Legacy signals. The paint does not create any voltage drops. Just make sure all your joints are tight when putting the track down. 

20150507_131905 

Looks great! I think the 3-rail track looks better with all rails the same real rail color, instead of a black center rail which calls attention to being different.

Ponz posted:

Thread revival!

What if I have Gargraves track with wood ties?  It seems the paint would be difficult, at best, to remove from the ties.

 

Thanks - Ponz

It depends on how you plan on painting the rails. If you are using a brush it really shouldn't be an issue keeping the paint off the ties. I used an airbrush and intentionally, (light coating) sprayed the tires with the same color as the rails. It gave it the dirty, oily look I was aiming for. 

 

Marc

Jacobpaul81 posted:
Ponz posted:

Thread revival!

What if I have Gargraves track with wood ties?  It seems the paint would be difficult, at best, to remove from the ties.

 

Thanks - Ponz

That's what I've got.  Rustoleum Camo Brown.  Easy to do and color blends with gargraves ties.

Thank you JacobPaul - that's what I was hoping to hear.  I'd prefer to brush it on, but I only see spray cans everywhere.  Any ideas?

Ponz

@domer94 posted:

thanks. im torn weather or not to go this route, or the airbrushing of the whole thing in one color.. sort of a dark dirty grey type of thing. ive seen it on the forum , but don't know the exact color. I kind of dig the rust brown look , but like the weathered look of all three as well.

Hi

I am also painting rails on my track, you have to wipe down the rails with alcohol to remove the oil put on during mfg, i use a oil base rustoleum primer for the first coat, i found some excellent paint for painting the rails it is microlux paint from micro mark in new jersey it comes in brushable or air brush paint and comes in 2oz bottles if you order a variaty of colors you can mix them together to come up with a color you like, i mix 1 drop of rail brown with another color to tone down the greenish color of the rail brown, just till you find the color that you like  then just write down the formula and you can mix larger batches i also found these touchup brushes used for automotive paint touchup on amazon that work great on the rails they look like a small Qtip but dont leave any cotton fuzz behind  they say they are throw away but i wash them with waater and use them multiple times i bought a pack of 100 of them for about $10.00 hope this helps.



Regards



Prentice

@domer94 posted:

I picked up a paint pen from wally world and tested it out on a piece of flex. it didn't adhere that great. should I wipe it down with something first?  also getting to the inside with that pen was a little tough.. should I just brush it? im just wondering if im opening a can of worms with this.

Hi

I am also painting rails on my track, you have to wipe down the rails with alcohol to remove the oil put on during mfg, i use a oil base rustoleum primer for the first coat, i found some excellent paint for painting the rails it is microlux paint from micro mark in new jersey it comes in brushable or air brush paint and comes in 2oz bottles if you order a variaty of colors you can mix them together to come up with a color you like, i mix 1 drop of rail brown with another color to tone down the greenish color of the rail brown, just till you find the color that you like  then just write down the formula and you can mix larger batches i also found these touchup brushes used for automotive paint touchup on amazon that work great on the rails they look like a small Qtip but dont leave any cotton fuzz behind  they say they are throw away but i wash them with waater and use them multiple times i bought a pack of 100 of them for about $10.00 hope this helps.



Regards



Prentice

@domer94 posted:

I picked up a paint pen from wally world and tested it out on a piece of flex. it didn't adhere that great. should I wipe it down with something first?  also getting to the inside with that pen was a little tough.. should I just brush it? im just wondering if im opening a can of worms with this.

I bought these brushes on amazon they were pretty cheap i think they were about $10-$15 for 100 of them they say they are disposable but you can wash them out with water if you are using a water base paint and use them a couple of times they work good and fit on the side of the track

Attachments

Images (1)
  • Rail Paint Brush

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Ste 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×