Skip to main content

9 replies

Question about Lionel 6-28223 2005 BNSF SD70 Diesel Locomotive

GS Greg SOGR Forum Member

I recently bought a used Lionel 6-28223 2005 BNSF SD70 Diesel Locomotive and whenever I power it up it ALWAYS starts in reverse.  I've tried to lock it into forward but as soon as you stop it and start it back up it goes in reverse.  It will go forward but you have to hit the direction button to get it to go forward.  It seems like it's reverse/neutral/forward no matter what I try.  I'm only using a CW-80 and my two other engines work just fine.  Anyone have any ideas on what might be happening?  Also, there is always a delay in it starting up, I usually have to set the throttle at about 50/60 before it takes off.  And I think one of the cab lights are out on it.  I took a few photos to show the light that is out I "think"   Thanks in advance!

Lionel 6-28223 2005 BNSF SD70

 

 

IMG_6838

IMG_6840

Attachments

Hide
Images (2)
  • IMG_6838: Looks like the light is out on the left hand side
  • IMG_6840: Looks like the light is out on the left hand side
Original Post

Replies sorted oldest to newest

GS Greg SOGR Forum Member
Originally Posted by falconservice:

It sounds like the wires or the wires to a switch are installed backwards.

 

You might have to get an official LIONEL wiring diagram to compare with what is inside.

 

Andrew

I thought about that and looked around but couldn't really find a wiring diagram.  It would seem kinda odd that it would be wired backwards wouldn't you think?  I found a wiring diagram for a SD80 but not the SD70

 

 

 

Originally Posted by Alfred E Neuman:

Turn the SD70 around and run in the other direction. 

 

 

 

 

What, me worry?

Heh.... I'm ashamed to admit it but I did that try that

WoodWoodOGR Forum Member SUPPORTING MEMBERDIGITAL SUBSCRIBER

If you bought it used then it may have been run in TMCC. It may have been set up as the trailing engine of a consist.  in that service the engine has to be set to start in reverse. I have done that on one of my SD70ACe engines.  The only way to get it out of reverse is to do a reset on the engine. I think you can do that in conventional operation. Check the operations manual or go on line and load it up from Lionel.

 

If that fails, find a friend and reset it in TMCC mode.

Last edited by Wood
GS Greg SOGR Forum Member
Originally Posted by Wood:

Oops, it is not a command engine.  I just clicked on the link. I would still try the reset option.

Thanks for the tip I've been searching for those reset commands but I can't find anything.  I only have a CW-80 transformer so I've been looking for some kind of reset command sequence but no luck.  Not even sure there is one for this specific engine?  Thank you again for the advice I'll keep looking and see what I can find.

Add Reply

Views: 487
Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Ste 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

Membership Required

We're sorry. You must be signed in to continue. Sign In or Register
×
Are you sure you want to remove from your Block List?
×
Loading...
×
When you block a person, they can no longer invite you to a private message or post to your profile wall. Replies and comments they make will be collapsed/hidden by default. Finally, you'll never receive email notifications about content they create or likes they designate for your content.
Note: if you proceed, you will no longer be following .
×
Link copied to your clipboard.
×

Access to this requires an OGR Forum Supporting Membership

OGR Forum Supporting Membership

Help support this forum with an OGR Forum Supporting Membership.
You will be able to watch the videos in the INSTRUCTIONAL VIDEO FORUM!
A one-year OGR Forum Supporting Membership is only $12 per year, so sign up now!


    OR     


Access the ALL the OGR VIDEO FORUMS AND  over 300 back issues of OGR
with a DIGITAL SUBSCRIPTION!



$12.00 per 12 Months (plus tax if applicable)
×