Setting stall speed on TMMC ?

Hi Clem,

I found the manual online here;

https://www.lionelsupport.com/...1250LegacyMohawk.pdf

Page 20 talks about setting the speed steps/momentum.

There are no "speed steps" to program.  To set the stall speed for a locomotive without cruise, do the following.

JRJ the manual posted just below my post shows speed steps ?  It does not mention stall speed but your video link does.

Clem

clem k posted:

JRJ the manual posted just below my post shows speed steps ?  It does not mention stall speed but your video link does.

Clem

The manual you posted is for a Legacy engine.  Legacy engines do not need a "stall" setting.  You can set speed steps for use with a Cab1 as well as preset momentum based on the speed step setting.

MartyE posted:

clem k posted:

JRJ the manual posted just below my post shows speed steps ?  It does not mention stall speed but your video link does.

Clem

The manual you posted is for a Legacy engine not a TMCC engine.  Legacy engines do not need a "stall" setting.  You can set speed steps for use with a Cab1.

Or TMCC engines using a CAB2

clem k posted:

Good morning

I have two Lionel Berkshire's, #6-11411 & #6-11412 and a Cab 1 #6-12969.  How do I program the speed steps,stall speed and momentum?

Clem

Hi Clem,

Is your goal to get these to run in sync? I know when we left one was running at a different cadence than the other.

I recommend doing a hard reset on both and see if this helps.

MartyE posted:

clem k posted:

JRJ the manual posted just below my post shows speed steps ?  It does not mention stall speed but your video link does.

Clem

The manual you posted is for a Legacy engine.  Legacy engines do not need a "stall" setting.  You can set speed steps for use with a Cab1 as well as preset momentum based on the speed step setting.

What "speed steps are you talking about for a plain TMCC locomotive.  AFAIK, it's 32 speed steps for TMCC or TMCC with Odyssey I.  Only if you get into 3rd party electronics like ERR, TAS, or K-Line do you get adjustable number of speed steps.

Guys I posted the product numbers of what I was working with. I just go with the information I have which is the owners manual. Lost the CAB 1 manual. Page 20 shows speed steps, and has a diagram and photo of my controller. Everything I asked is a question, I don't know Lionel products.  These are the only two I have.  

J Daddy posted:

clem k posted:

Good morning

I have two Lionel Berkshire's, #6-11411 & #6-11412 and a Cab 1 #6-12969.  How do I program the speed steps,stall speed and momentum?

Clem

Hi Clem,

Is your goal to get these to run in sync? I know when we left one was running at a different cadence than the other.

I recommend doing a hard reset on both and see if this helps.

HI John..... I got them working in sync. Took all day,  but I got them working.

Clem

Thank you everyone all is right in my little world   

Clem

As previously mentioned, as long as Odyssey II is turned on for the two Legacy locomotives, they should be pretty much in lock-step.  I think we got led astray thinking these were TMCC.

What is Odyssey II ?   I run these with Cab 1 and the DCS remote. Plain old TMCC

Clem

Odyssey II is the speed control on all DC motored Legacy locomotives.  TMCC had an earlier version of the speed control, oddly called Odyssey I.

OK   that last thing I knew about Odyssey is that it was some kind of new electric motor Lionel was developing 

Funny, every Legacy locomotive on the Lionel site has the following statement in the description.

• Odyssey® II Speed Control with On/Off switch

If you look at any of the Odyssey I equipped TMCC models...

• Odyssey System for speed control

You living in a cave somewhere?