Skip to main content

Replies sorted oldest to newest

Here is what I am working on for the Hidden Pass Junction RR. The panel itself is complete other than I have to add (insert from behind) the LED's at each turnout. The panel is 18" x 36", and I am working on the wiring now.

 

Control Panel 02 med crp2 DSC_0400

 

I'll post more pictures later today or tomorrow under a separate thread. (I am just testing the new forum posting   )

 

Alex

Attachments

Images (1)
  • Control Panel 02 med crp2 DSC_0400

DSCF0069

DSCF0070

This is mine ,
The black strip in front of the transformers is for operating accessories .
All my switch activation buttons are in the schematic and signal a building light switches are to the side.
Everything is hinged for easy access.
I think it turned out pretty good for a Half *ssed carpenter like me.

David

Attachments

Images (2)
  • DSCF0069
  • DSCF0070

I built my train table on top of kitchen cabinets.

I built my control cabinet in a modified 'sink base'

Two pictures are enclosed, one of the bottom which contains lots of horsepower and the top which contains the panel.

This rolls in and out when necessary with a set of cables from the rear to stationary panels to prevent wires from breaking.

This is all still part of my layout, however there is nothing in that panel which I now CANNOT run directly from my DCS handheld.

If I were starting from scratch, I would bury all transformer power and run all my Conventional, DCS and TMCC from my handheld as I do now.

Attachments

Images (6)
  • DCS10: DCS added more wires
  • DCS11: Cableing system
  • DCS12: 5 Aiu's required for remote
  • DCS13: "Only the shadow knows..
  • DCS14: Transformer power
  • DCS15: Before DCS
Originally Posted by rrman:
"I don't need no stink'in control panel, they're all in my DCS handheld!!"
My previous layout had a large panel with switches and LEDs, but then I saw the (DCS) light and I never looked back.

Here is my new panel after my DCS installation. Light switch at the right end powers up all the transformer power needed for my layout. The other two switches turn my (1)lighting (2) signal circuits on/off. Still have room for one more switch, but cannot figure out what for?
All the best,
Hugh

100_0054

Attachments

Images (1)
  • 100_0054
Originally Posted by nickaix:
Originally Posted by ADCX Rob:
"Old School":

Wow---proving once again that there is nothing like the old stuff for sheer impressiveness!

And look at the expression on that young man's face as he drives his train the old fashioned way. You don't get that kind of satisfaction from pushing buttons on a TV remote... unless it is a TV remote and you're pulling up an Anita Ekberg movie on TCM.

Pete

My panel was designed on the computer.  All of the RR logos were designed by me or copied from the internet.  Before I print them, the original design is converted so that all of the little lights and switches that are seen on the drawing become little hash marks or crosses.  This makes it clear as to where drill all of the holes precisely.  It is then sent out to the printer, such as Kinko's or OfficeMax, to be print on a high resolution color laser printer.  Once printed, it is laminated, trimmed and mounted on very thin plate steel to give it rigidity and strength.  Holes are drilled and devices mounted, wired, and tested.  The frame is installed and finished to the customers specs.  All of the wiring is finallized through the back cover and landed on marked and labeled terminal strips for easy hook-up to the layout.

Originally Posted by dave hikel:

New school.

 

 

I'm a big believer in form following function, so if those panels work properly for their owners I'm down with that. But man their appearance is incredibly boring compared to old school. Hands down the best panel so far is BobbyDing's. There's just no accounting for taste, eh.

 

Pete

Yikes.
Got some track down and one of these days I have to start running some wires.  Hugh, your 6 photos from Feb 2 are beautiful but scare the bejeekers out of me.
I am planning for DCS.  A few questions for the wiring gurus:

1) Hugh, "If I were starting from scratch, I would bury all transformer power..."
If I leave the handles on my Z4000 up when I power it off, then when I power back up it outputs garbage and I have to cycle the handles down and back up by hand to starighten it out.  Is this just me, or do I have to have my Z4000's out on a shelf where i can get to them every time i power up? is there some way around this? The outlets in the train room are controlled by a relay, with one wall switch by the door so when I leave I know everything is off, and everything can come on with one switch when I come in. Except for the z4000's?

2) Hugh, " ...run all my Conventional, DCS and TMCC from my handheld as I do now."
and rrman, ""I don't need no stink'in control panel, they're all in my DCS handheld!!"
My previous layout had a large panel with switches and LEDs, but then I saw the (DCS) light and I never looked back."
I know this is how DCS is designed and works, but are you guys seriously saying that you throw all your turnouts by scolling around on that handheld instead of just toggling a switch on a schematic panel?  I just can't imagine it would be anywhere near as convenient.  If so, then great! no need to build a control panel.  But it seems like you gotta push a lot of buttons to get to a turnout on the hand held?

3) this will really show my ignorance, but both Hugh and ChoCho Bob look like you're using the long white telephone punch-down terminal blocks.  Can't see from the photos what wires you are running to them and can't think why you'd have so many wires going to one block unless... are you using these for your commons?

thanks
Originally Posted by hojack:
I know this is how DCS is designed and works, but are you guys seriously saying that you throw all your turnouts by scolling around on that handheld instead of just toggling a switch on a schematic panel?  I just can't imagine it would be anywhere near as convenient.  If so, then great! no need to build a control panel.  But it seems like you gotta push a lot of buttons to get to a turnout on the hand held?


Not really, just push SW on handheld and scroll to turnout (or punch number key) and press normal or diverging icon.  Saves having to walk to panel each time to flip switch.  Handheld allows up close operation and if turnout didn't throw or some obstruction you can stop train before consequenses.

Originally Posted by rrman:

Not really, just push SW on handheld and scroll to turnout...  Handheld allows up close operation

Point taken.  thank you.  no control panel.   wait while i wrap my head around this.  

  

The other thing would be toggles for all the sidings.  Since I am doing standard gauge tinplate, the aesthetic calls for the knife switches like on the 439 panel or the switch tower buildings.  Are these knife switches satisfactory to use with DCS or should I use new toggles?  Does DCS signal degrade through the knife switches? 

When designing my new layout I first had the idea to have no control panel as I plan to run 100% command control with my Legacy controller. After much thought I knew I would want yo reach over an flip a switch or two. I'm sure glad I decided to build the panel!

 

Most all toggle switches, terminal strips, wiring supplies and LEDs came from Demar Electronics. Great company to deal with. They had just what I needed and were helpful to make sure I ordered what I really wanted.

 

I wanted the panel below table top so to not interfere with a view of the trains. I also wanted easy access to wires. The panel opens from the center to make wiring easy.

IMG_1978

 

All of my switch tracks, Ross with DZ 2500s and K-line Super Snaps are controlled by either SC-1s or SC-2s

IMG_1975

 

Rather than have a jumble of wires at the back of the control panel, I built a "power distribution" center and it has worked out very well.

IMG_1976

IMG_1977

 

 Transformers are neatly arranged below table and are easilly reached to turn up power on the ZWs which serve the five power districts. The KWs power accessories.

 

Stan

 

 

 

 

 

 

Attachments

Images (4)
  • IMG_1978
  • IMG_1975
  • IMG_1976
  • IMG_1977
Last edited by stangtrain

All controlled with a Cab-1.  There are (2) BPC (Block Power Controllers) controlling (8) power districts. (1) TPC (Track Power Controller) that turns it all on an off. and (6)ASC's (Accessory Switch Controllers) (5) controlling 20 switches and (1) controlling  8 accessories.

   

This is my setup. I jumped on board with the controllers early. It's just the way I started. Most of my controllers are original IC Controls boxes. I love it. Been working great for 8/9 years.  3 bricks for power//-2 TPCs-1 for TMCC-1 for conventional operation//-2 BPCs-can switch 8 blocks of track from TMCC to conv//-4 ASCs-3 for 12 switches-1 for accessories//- 2 OTCs-1 for 4 Uncouple tracks-1 for 2 operating tracks//- 2 AMCs-1 to run log loader and lights on layout-1 for  magnetic crane and light in blacksmith shop- (voltage outputs are adjustable on AMC-great for fine tuning power to  tricky accessories)//-1 ARC-for recordings-works awesome// Command Base// Accessory power pack//Cab 1s to make it all go-all is operated by the Cab 1 remote  

moxie pics 016

Attachments

Images (1)
  • moxie pics 016
Last edited by William 1

Add Reply

Post

OGR Publishing, Inc., 1310 Eastside Centre Ct, Ste 6, Mountain Home, AR 72653
800-980-OGRR (6477)
www.ogaugerr.com

×
×
×
×
Link copied to your clipboard.
×
×