Skip to main content

For those owners who have taken their observation cars apart to add figures, did you notice the mounting points in the bodies are different from the other cars?

I ask because I found when taking my Union Pacific Observation "City of San Fransisco" apart there were no mounts to screw the frame into the body on the rear end. It appears there are screw mounts in the roof that long screws or a threaded adapter was meant to be used but isn't there. Do other cars have these adapters or long screws? Is this setup unique to the UP Excursion cars? 

The only thing holding the body to frame before taking it apart was the excess adhesive used for the windows.

Front end of the car with typical screw mounts in the end bulkheads.

Rear end with screw mounts in the roof.

With the excess glue removed the frame now slides off the body by just picking it up.

Pete

Attachments

Images (2)
  • image
  • image
Original Post

Replies sorted oldest to newest

Yes, I have seen that in the same kind of car you picture. I think that there are holes in the frame, and certainly in the plastic interior assembly, for long screws to be inserted. But if they had been, they’d be visible squarely in the two side windows at the end of the car. That is the only reason I can think of why they were not installed at the factory.

On another thread about these cars, someone posted that they had worked out the length and diameter of the (metric) screws needed for the purpose of using the mounts in the roof of the car. I have thought about affixing a piece of something, probably plastic, at the base of the car body that shorter screws could be drilled into. Have not got around to trying that.

Meanwhile, you can always put in some ultra-sticky double sided tape . . .

P.S. Here’s the thread where this was discussed: https://ogrforum.com/...54#80410241313147254

The screw measurement was 3 mm diameter x 60 mm length.

Last edited by Hancock52
BobbyD posted:

Can you glue a triangulated piece just above the floor in both corners to screw into leaving the windows unobstructed?

It's slightly awkward because those corners are not 90 degree angles; see photo below. Plus you have to get rid of all the excess double-sided tape and the side window edges are very close to where the mounts would be fitted.

UP_Excur_Bodywork_copy2

My idea, which won't be better than Pete's, is to glue in a mount on the flat end of the car and provide for a single screw through it to hold the rear of the car's body in place. That means drilling through the metal frame and possibly cutting away a small part of the interior molding but neither is any big deal.  On mine I am planning on fitting an illuminated tail sign near that position so some of the body will have to be trimmed away in any event.

Attachments

Images (1)
  • UP_Excur_Bodywork_copy2

I am working on a fix guys. Film at eleven. 

As for the adhesive, I just rubbed it off along the depression in the dome cars. All the rest I just covered with scotch tape which can be seen at the top pic above. Eliminates all sticking and as pointed out the frame falls out of the end now that is not screwed to the body.

Pete

Hancock52 posted:
BobbyD posted:

Can you glue a triangulated piece just above the floor in both corners to screw into leaving the windows unobstructed?

It's slightly awkward because those corners are not 90 degree angles; see photo below. Plus you have to get rid of all the excess double-sided tape and the side window edges are very close to where the mounts would be fitted.

UP_Excur_Bodywork_copy2

My idea, which won't be better than Pete's, is to glue in a mount on the flat end of the car and provide for a single screw through it to hold the rear of the car's body in place. That means drilling through the metal frame and possibly cutting away a small part of the interior molding but neither is any big deal.  On mine I am planning on fitting an illuminated tail sign near that position so some of the body will have to be trimmed away in any event.

Don't they come with an illuminated one? It is nice to see the windows are "flush" now.

BobbyD posted:
Don't they come with an illuminated one? 

Nope. I have not got an end on photo of my own to show you but I borrow the one below from another Forumite:

IMG_7798 copy

There are three nice LED taillights shown illuminated in my photo below but the rear door is blank.  I have found a photo of a tail sign UP used which I intend to install with an LED mounted behind.

City_Of_San_Francisco_Dome copy

Attachments

Images (2)
  • IMG_7798 copy
  • City_Of_San_Francisco_Dome copy
Hancock52 posted:

There are three nice LED taillights shown illuminated in my photo below but the rear door is blank.  I have found a photo of a tail sign UP used which I intend to install with an LED mounted behind.

City_Of_San_Francisco_Dome copy

Will you be doing a period City of Los Angeles or a modern era version with a UP Flag Shield?

I think all of the modern era trains I have seen, the City of San Francisco is sitting somewhere in the middle and a Business Car or theater car is last which may explain why Lionel didn't put a drumhead on this car.

I am hoping I can get a Kenefick Car for my train and add the drumhead above.

Pete

Last edited by Norton

I detailed both the UP Executive and Challenger Observations and did NOT make any modifications to the car because it was unnecessary.  Yes the posts are visible if you look for them, but with people in the car, viewers will be drawn to the people inside and not the vertical post. I also did not alter my two Pennsylvania Observation cars when I painted seats and added Presier 65602 Seated People that I painted. The 21" Pennsylvania Observation cars are similar.

Draw attention away from the posts by the placement of the people in your car.  The rear car body rests on the chassis plate when assembled. It is screwed in the front and the rear assembly is adequate to hold the car together.  Once it is on the track, there are no issues.  Adding a drumhead is nice, but will this always be your last car on the train?

There are times when Lionel's designs need owner modifications.  I do not believe this is one of those times. 

Sincerely, John Rowlen

Attachments

Images (6)
  • DSCN4675
  • DSCN4676
  • DSCN5264
  • DSCN5266
  • DSCN6772
  • DSCN6768
Last edited by John Rowlen
Norton posted:
 
Will you be doing a period City of Los Angeles or a modern era version with a UP Flag Shield?
 
I’ve tracked down a “period” tail sign (as in late in the City of San Francisco’s service life) and I am planning to use that unless I can find something better. Apart from anything else it is rectangular and can be scaled to fit.
 

I think all of the modern era trains I have seen, the City of San Francisco is sitting somewhere in the middle and a Business Car or theater car is last which may explain why Lionel didn't put a drumhead on this car.

Agreed. 

I am hoping I can get a Kenefick Car for my train and add the drumhead above.

I know that feeling but I have had no success trying to track down a good K-Line UP business car and in any event I already have the UP theater car.

 

Ok, this is what I have come up with. I still have to clean up the rough edges and paint it but will hold off until I decide what color to do the interior with. I think UP may actually have this interior on their site.

The part is made of copper clad epoxy circuit board with brass tubing and brass threaded spacers.

Fitted to the car. Note the scotch tape over the adhesive. The frame now drops out after the screws are removed.

How it appears from the rear.

image

And from the side.

The length of the thread spacer was determined by seat back height. If I had to to this over I might carve enough of the seat back so this adapter could sit below the window. It will get painted to match the seat so likely not noticable as the car whizzes by.

Pete

Attachments

Images (4)
  • image
  • image
  • image
  • image
Last edited by Norton

That is both impressive and ingenious. Sad to say I have NO metalworking skills whatsoever and could not duplicate this. In fact I have just ordered a quantity of Plastruct ABS glue to carry out the exercise I have in mind to deal with this issue on my City of San Francisco car. 

I will say that I am sure that in the finished car this structure won't be obvious. Most Lionel and indeed GGD boat tail observation cars have a long screw plainly visible in the rear of the interior of the car because it holds together the whole roof and rear exterior panel assembly. Your solution avoids that. 

Norton posted:

Ok, this is what I have come up with. I still have to clean up the rough edges and paint it but will hold off until I decide what color to do the interior with. I think UP may actually have this interior on their site.

The part is made of copper clad epoxy circuit board with brass tubing and brass threaded spacers.

Fitted to the car. Note the scotch tape over the adhesive. The frame now drops out after the screws are removed.

How it appears from the rear.

image

And from the side.

The length of the thread spacer was determined by seat back height. If I had to to this over I might carve enough of the seat back so this adapter could sit below the window. It will get painted to match the seat so likely not noticable as the car whizzes by.

Pete

Hi Norton,

Here are some color shots of a UP 9000 series Dome Observation car to help in your search.   Also, in the 1955 UP Domeliner video around the 2:45 mark it shows guests inside a 9000 series car (but this film is in black & white).  https://www.youtube.com/watch?...6ZsoEdJuc&t=431s

Attachments

Images (4)
  • 9000, dome COLA
  • 9000, COLA
  • 9000, COLA bar
  • 9000 dome film2
Norton posted:

Thank you for the link T. I admire your work. You and Hancock52 are real artists.

I am already working on the MKII mount to replace the one above.

Pete

1.  Have a look at T's thread on his UP dining car if you need any more inspiration: https://ogrforum.com/...enger-car-8003-k4690

2. MKII ???

3.  P.S. I think that this is already well known but the present-day City of San Francisco dome-lounge-observation car is depicted on the UP historical equipment site as shown below. I could be wrong but I think it was one of the cars being pulled behind Big Boy 4014 recently:

Screen Shot 2019-05-29 at 11.59.48 AM

Inside it now looks like an old-fashioned hotel saloon bar, IMHO. I actually prefer the original treatment T has documented, which has a more homespun feel to it.

Attachments

Images (1)
  • Screen Shot 2019-05-29 at 11.59.48 AM
Last edited by Hancock52

I have been following T's work. Very impressive. You guys should team up with Jack Pierce with his lighting effects. 

I am redesigning the mount so it won't be visible in the rear window. Now that I have the critical dimensions this should go pretty fast.

I think the City of San Francisco was also used in the Bush Funeral Train where I saw the pictures.

Pete

Last edited by Norton

Now for the 2nd generation mount. The seats were milled to allow lower placement of the bracket. Lower center portion removed to allow passengers to now exit the car. 

Gen 2 right.

Aisleway and seat fit. Section on the seat will get painted to match the seats. Brass uprights might just remain brass.

New rear view.

Pete

Attachments

Images (3)
  • image
  • image
  • image

I was thinking this morning of making one out of styrene. The top piece would be thicker as would the piece on top of the seat back. The threaded standoff at the bottom would either have to remain metal or if it was plastic have to be a larger diameter and material removed from the back of the seat. The metal standoff is pretty thin and a plastic copy the same size would likely split as soon as you put a screw through it.

Pete

I just finished relocating the couplers on all of my UP passenger cars. The last one was the Observation from the Challenger set. Turns out this car did come with supports to secure the rear body to the frame unlike the Excursion Observation. Also it was devoid of extra tape below the widows so it came apart easily. As this set came out about year after the Excursion cars it looks like changes were made at the factory to do a better job. 

No idea if Lionel will make these available to owners of cars where these are missing.

Clearly visible in the rear window.

Pete

 

Attachments

Images (2)
  • image
  • image
Last edited by Norton

I would guess that those threaded supports were not available when the Excursion cars were produced and the factory improvised. In any case Lionel has not been great about having spare parts for the second run of 21” ABS cars. 

Your solution is clearly better than the stock parts. I am still aiming for something simpler, which I might get to next week.

Hancock52 posted:
BobbyD posted:

Can you glue a triangulated piece just above the floor in both corners to screw into leaving the windows unobstructed?

It's slightly awkward because those corners are not 90 degree angles; see photo below. Plus you have to get rid of all the excess double-sided tape and the side window edges are very close to where the mounts would be fitted.

UP_Excur_Bodywork_copy2

My idea, which won't be better than Pete's, is to glue in a mount on the flat end of the car and provide for a single screw through it to hold the rear of the car's body in place. That means drilling through the metal frame and possibly cutting away a small part of the interior molding but neither is any big deal.  On mine I am planning on fitting an illuminated tail sign near that position so some of the body will have to be trimmed away in any event.

Hi Hancock, were you able to finish your "City of Los Angeles" tail sign?  

I'm finishing a new flat/blunt end for my K-line passenger car and was looking for some ideas on the CoLA tail sign.  Did you make your tail sign with plastic or aluminum?  As you suggested in a previous post I'm going to print my own graphics but did you use micro LED's or 3mm in your sign?  If so, how many LED's?

Thanks,

COLA sign 2

 

Attachments

Images (1)
  • COLA sign 2
Last edited by T.Albers

No, haven't got around to doing the tail sign yet - and what I found in terms of an image is not a patch on what you have! I'd have to do it in plastic - no metalworking skills - but I have learned to use metal finish paints that can produce a good facsimile of the real thing.

I can help more on the tail sign illumination. Basically I have found that multiple smaller LEDS, say 4 or even 2, are better than one LED of any significant size. A 3 mm will LED throw a lot of light out but in a straight beam so you end up with a hot spot in the sign. Plus you will get reflected light bouncing back behind the LED so it has to be sealed off from the interior. A single incandescent bulb of roughly the same size as a 3 mm LED will spread the light better but they burn out and replacement is a big deal unless you have built your interior to accommodate that. 

I also tried disc-shaped flat LEDS but they only come in larger sizes and the light is really too intense for this purpose.

 

Just as a postscript, while doing a little research on the tail sign options I found this image of the CoLA sign on the CoSF car, which shows the neon lighting:

1F213547-814A-4C8A-8905-E07ECC092EE1

Not sure that I will try to model this as it would mean cutting away part of the diaphragm on the rear of the car to install it. But if I did, the graphic would require a little work to blacken the background behind the lettering. A fiddly job but could certainly be done. I’d print the image on an inkjet printer transparent sheet and cut it to fit in the housing.

The shape would require multiple lights to illuminate the whole. Evan Designs make a track-powered set of four LEDs that I have used before for internal car lighting. This would allow three lights across the main horizontal part and one behind the “Domeliner” lettering.

 

Attachments

Images (1)
  • 1F213547-814A-4C8A-8905-E07ECC092EE1

Hi Pete & Hancock

I tried to make that CoLA neon tail sign out of plastic with three LED disk lights.   But as Hancock52 recommends above I should have used multiple smaller LED lights to lessen the chance of bright hot spots showing through the tail sign.

 

Also, I wanted the neon tail sign box look shiny but was not getting this effect using silver paint.  The box above still looked plastic.  So, I gave up on the plastic design and made second tail sign by bending a thin sheet of flat metal.  Then installed six, 3-volt micro LED’s and wired them in series,  That way the lights could handle direct 18-volts from the track.

Also, I followed the advice above to get the neon effect I used four layers on the sign.  The bottom layer was clear plastic, the 2nd layer was 20 weight white paper (as recommended by GRJ in another posting), the 3rd layer was a black and white City of Los Angeles sign and finally on top was the full color City of Los Angeles sign.  That way, whether the LED lights were shining or not it would still look like a neon sign.

T.Albers posted:

Hi Pete & Hancock

I tried to make that CoLA neon tail sign out of plastic with three LED disk lights.   But as Hancock52 recommends above I should have used multiple smaller LED lights to lessen the chance of bright hot spots showing through the tail sign.

 

Also, I wanted the neon tail sign box look shiny but was not getting this effect using silver paint.  The box above still looked plastic.  So, I gave up on the plastic design and made second tail sign by bending a thin sheet of flat metal.  Then installed six, 3-volt micro LED’s and wired them in series,  That way the lights could handle direct 18-volts from the track.

Also, I followed the advice above to get the neon effect I used four layers on the sign.  The bottom layer was clear plastic, the 2nd layer was 20 weight white paper (as recommended by GRJ in another posting), the 3rd layer was a black and white City of Los Angeles sign and finally on top was the full color City of Los Angeles sign.  That way, whether the LED lights were shining or not it would still look like a neon sign.

T, next time you want a chrome like finish, this will do it. Apply it wet and it will dry like polished aluminum near chrome.

Pete

Attachments

Images (1)
  • image

Composite response:

Pete, not making it to York this time, unfortunately, but I'll gladly take the diaphragms you have off your hands if we can arrange something. I'll drop you an email. Your offer pushes me over the edge and I will try constructing the proper CoLA sign.

T.Albers, if you were posting two photos of your tail sign they didn't come out, or not on my Mac devices, and I'd be keen to see them. The Molotow recommendation is right as I have used it although I have not tried airbrushing it yet. It is HIGHLY reflective but is an ink, not paint, and so takes some careful handling. If I was willing to give away the latest phase of my UP Excursion cars project, which I can't until it's further along, I'd show the latest use I have made of it. Straight out of the pen/applicator it works like a treat on small detail/accent parts. I'm pretty sure that bigger/flat surfaces require spraying.

Sorry Guys, Let me know if you get the 2 photos this time. 

1st photo should be show plastic tail sign box with 3 disk LEDs  

Neon tail sign plastic

2nd photo should be metal tail sign box (.008 thick from K&S Precision metals) with 6 micro LEDs

Neon tail sign metal

Hancock, I had know idea about that liquid chrome finish.  It looks like a good product.  Lol, it would have saved me having to cut and bend a new tail sign out metal.  After filing and polishing that new metal sign it got real sharp and drew blood a few times! 

Attachments

Images (2)
  • Neon tail sign plastic
  • Neon tail sign metal

T, I have air brushed Molotow and it will give a very shiny finish; comparable to the finish on LIONEL's shiny anodized passen ger cars; e.g., Texas Special, Santa Fe, California Zephyr, etc.

It is an ink as H52 mentioned--don't handle it for 24 hours; needs clearcoat (IMO) since it will come off with iso alcohol.  Numerous useful YouTube videos on spraying Molotow.

My use will be to spray it on some Evergreen corrugated siding to attach to an F-3 to simulate the stainless steel used on the Texas Special E-7's.  My test sprays show this will be an effective alternative for my purposes.

Thanks for posting the photos of your sign boxes.

Farmerjohn, GGD has certainnly acquired new buyers who, like you, have been disappointed by LIONEL's efforts.

Last edited by Pingman

Add Reply

Post
×
×
×
×
Link copied to your clipboard.
×
×